Wireless Video Repeater

The repeater consists of a receiver and a transmitter built inside an weatherproof enclosure. The receiver receives the video signal in a preset frequency (say Channel 4), and the transmitter sends the video signal out in another preset frequency (say Channel 1). The repeater may be used: (a) as an intermediate booster to extend the transmission distance; or (b) to avoid obstacles in the transmission path by changing the direction of the source signal. The repeater is designed for use with our 1.2GHz transmitters/receivers here, or other compatible transmitters/receivers. See how it works here.

For indoor non-weatherproof model, please visit this page.

Use video transmitter module with stable output power.
Use high reliability/linearity/AIGaAs/GaAs FET amplifier module.
Use high reliability and sensitivity Comtech tuner module
Adopt phase locked loop circuit to eliminate frequency drift.

Transmission range
Range may vary substantially depending on the actual operating environment. Longer distance can be achieved if high gain directional antennas are installed in a line of sight environment. Estimated maximum transmission distance in an unobstructed environment between two static points using 12dBi Yagi directional antennas on both sides is about 40 miles (64 km).
Specifications Receiver Side Transmitter Side
Modulation FM demodulation / modulation
Number of Channel  1 channel fixed at CH4 (1200MHz)
(see Note below)
1 channel fixed at CH1 (1080MHz)
(see Note below)
Antenna included No antenna included (see Note 1 in Antenna Note section)
Antenna connector type N (F)
Operating power DC 12V (100~240V regulated AC/DC power adapter included)
Voltage/Current consumption 12V / 4 watts (0.35A) 12V / 15~42 watts (1.25~3.5A)
Dimensions 20(L) x 15(W) x 8(H) cm
Weight 1.5 kg excluding the antennas
Video output/input 75 Ohm 1V p-p
Audio output/input 10k Ohm 2V p-p max. 2V p-p, max
Power input connector DC jack for 5.5 mm plug
Sensitivity/Output power Sensitivity: -85 dBm (typical) Output power: 3w, 5W or 10W
Audio sub carrier frequency 5.5 MHz
Impedance 50 Ω
Highest video resolution supported NTSC: 768(H) x 494(V) / PAL: 752(H) x 582(V)
Compatible video standard NTSC and PAL
Operating temp/RH -10~+50°C / 20~80%

Note: We may change this channel to either 1080, 1120, 1160 or 1200 MHz if you request. But the channel setting of the Receiver and the Transmitter must not be the same.

Antenna notes
1) If the transmission path is line of sight, it is recommended that Yagi directional antennas, panel antennas or other directional antennas be used on both sides of the video repeater.
2) It is recommended to use antennas of at least 9dBi gain or above (option item) for the repeater.
3) Maintain a minimum distance of 2 meters (approx. 6.5') between the front and back antennas in order to avoid self interference. This can be acheived by using antenna extension cables.
4) If it is necessary to use antenna extension cable, the cable should be kept as short as possible because, the signal attenuates directly proportional to the length of the cable, i.e. the longer the cable, the weaker the signal from the antenna.
Packing contents
1) One video repeater; and
2) One 12V universal regulated AC/DC power adapter.

Left side / Right side

Move mouse over the picture to zoom


Add a high gain directional antenna(s) for the transmitter/receiver? **

** UPS delivery option is not available for these antennas except panel antenna.

Add an extension cable for the antenna(s) ordered?

This is a SSL secured site for online shopping

Pay securely with major credit card