This 2.4GHz digital video transmitter enables you to send video from one location to another without expensive and messy wiring. Video only, no audio. It works with all types of wired video camera (NTSC or PAL, analog or digital). See a sample system setup here. The transmitter kit works with camera with or without PTZ features.
The transmitter works on its own transmission system and is therefore particularly useful in those locations where there is no internet coverage or out of WiFi range. No internet connection required. No bandwidth to worry about.
The transmitter sends video signal wirelessly to the included receiver. Transmission effectively avoids common radio interferences caused by other wireless equipment such as blue-tooth, cordless phone, WiFi etc. operating in the vicinity. Random ID coding between the transmitter and the receiver secures the privacy of video transmission.
Move mouse over the picture to zoom
Transmitter. Video signal sent out from the transmitter can only be received by a receiver matching the random ID code. The pairing process between the transmitter and the receiver can only be done within a 3-meter range. A transmitter can only be paired with one receiver at a time. BNC video input plug for video input from video camera.
Receiver. By pressing the "pair" button on the receiver, it will automatically pair with the transmitter using a pseudorandom sequence for a channel with random ID code, which is only known to both the pairing transmitter/receiver. RCA output jacks of video on the front panel for connecting to a display device such as TV, monitor, DVR, computer....
Viewing live video feed over the internet or mobile phone. If you have a DVR and other equipment connecting to the internet, you may connect the wireless receiver to one of the video inputs of your DVR so that you can view the camera footage live in a remote location over the internet or on your cell phone. A sample setup can be found here.
Frequency Hopping Technology. Adopting Frequency Hopping Spread Spectrum (FHSS) and auto pairing with random ID to avoid unauthorized reception, interception or jamming. These technologies also substantially reduce interferences from other sources of radio disturbances to ensure a steady and quality video stream.
RS485 interface. This transmission system not only allows you to send video from one location to another. It also gives you the ability to control the Pan/Tilt/Zoom movements of your PTZ camera via the RS485 wires on the receiver, through a PTZ keyboard, a DVR with PTZ control functionality or other PTZ controller. The PTZ protocol supported by this system is Pelco P or Pelco D (auto detected). The baud rate supported is 2400 bps.
Easy installation. Set up can be completed within minutes.
|Modulation||COFDM - 16QAM, QPSK, BPSK|
|Video standard||NTSC and PAL compatible|
|Privacy||Adopting FHSS hoping and auto pairing with random ID codes to protect privacy and minimize RF interferences|
|Channel selection||26 channels, auto-selected during pairing|
|Frequency range||2400~2480 MHz|
|Resolution/Frame Rate||NTSC: 720 x 480/30 FPS; PAL: 768 x 576/25 FPS|
|Receiver Sensitivity||-88 dBm (typical)||N/A|
|Video data transfer rate||up to 12Mbps, typical 6Mbps|
|Output Power||N/A||200 mW|
|Transmission Range||Up to 300 meters (1000 feet) line of sight with standard antennas. Longer distance can be achieved if high gain directional antennas of 12dBi or above are installed on both sides in a line of sight environment: 5 km (3 miles)|
|Video Outputs/Inputs||BNC male connector|
|Antenna connector type||RSMA-F|
|Antenna included||3dBi omni-directional rubber duck antenna (RSMA-M)|
|RS485 Interface||Supports Pelco P or Pelco D protocol (auto-detected). Baud rate: 2400 bps.|
|Waterproof housing rating||IP66|
|Power voltage/consumption||DC12V/1.9W (current draw 500 mA)|
|Operating temperature||-10o C ~ +50o C|
|Dimensions / weight||160(L) x 123(W) x 37(H) mm / 230 gm excl. antenna|
2. A digital video receiver with a composite cable for video, 12VDC power and RS485 connections.
3. Two 3dBi dipole antennas.
4. Two screw terminals for the RS485 wires.
5. Two universal regulated 12V 100~240V AC/DC power adapters.
6. Installation guide.